Jump to content
Monthly Subscriptions Are Here Read more... ×

Search the Community

Showing results for tags 'tcp tunnel'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Features Discussion
    • Getting started
    • Release Notes
    • General
    • Feedback & Feature Requests
    • Agent
    • User Portal and Web App
    • Domotz Mobile App
    • Domotz Hardware
  • Third Party Hardware
    • Power Distribution Units (PDU) & Smart Power Plugs
    • Managed Network Switches
    • Gateway/Controller Integrations
    • Wi-Fi Access Point and Controllers Integrations
    • Audio Video and Multimedia Integrations
    • Other Devices
    • Domotz Agents on 3rd party platforms

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Found 6 results

  1. travislpriest

    TCP Tunnel - Q-Sys Designer from remote

    Hello, Here's how to connect to a remote QSC Q-Sys Core via Domotz. These directions and the attached script are based off the Extron from remote thread. I've modified the script to work with the ports Q-Sys uses. Q-Sys Instructions 1. Select the Q-Sys Core from the Domotz WebApp → Device list → Device 2. Go to "Connect" tab 3. Click on "Open a TCP tunnel" 4. Insert the TCP Port. By default you will need to open 3 tunnels for the following ports: 80, 1700 and 6504. 5. Wait to have the tunnel setup 6. Repeat steps 3 and 4 for each port. 7. You will have a host and a port for each TCP Tunnel (see the Extron thread linked at the top for screenshots). 8. Open the .bat file as Administrator (see link below) and enter the requested information on the screen. 9. Add a hard link within Q-Sys Designer following QSC's documentation and use the loopback address you chose (e.g. 127.0.0.100). Note: Make sure the mode is set to HTTP. You should see it turn green. 10. Click OK, then File -> Load from Core & Connect and you should see the Core listed there to connect to. Domotz Q-Sys Connect.bat
  2. henriquesalvador

    TCP Tunnel - Lutron from remote

    Hi all, This is all the steps to connect from remote to your Lutron Processor using Domotz Pro: Lutron Instruction Select the Lutron Processor from the Domotz WebApp → Device list → Device Go in "Connect" tab Click on "Create a TCP tunnel" Insert the Lutron Processor TCP Port. By default "51023" Wait to have the tunnel setup You get two information: Host Port Open Lutron Designer program on your Laptop and: Activate -> Processors --> Remote Access form Insert the previously retrieved Host/Port to be inserted here (see attachment as an example) Save & Apply Now you can use your Lutron tool to to remotely access to the processor: a. Designer+ Tool for Lutron HomeWorks QS: b. Lutron RadioRA 2 System Overview for Lutron RadioRA: Go to the Find Main Repeater Screen from here in the Design Tab And select Advanced, then Remote for System communications as shown here: He should also have had a previous transfer without the checkbox being selected “Restrict Communications to Local LAN”. Let us know if you have any problem. Henrique Salvador Domotz Support  support@domotz.com
  3. henriquesalvador

    TCP Tunnel - Extron from remote

    Hi all, This is all the steps to connect from remote to your Extron controller/Panel using Domotz Pro: Extron Instructions 1. Select the Extron device from the Domotz WebApp → Device list → Device 2. Go to "Connect" tab 3. Click on "Open a TCP tunnel" 4. Insert the Extron TCP Port. By default you will need to open 4 tunnels for the following ports: 22022, 4522,4502 and 4503. 5. Wait to have the tunnel setup 6. Repeat steps 3 and 4 for each port: 7. You will have a host and a port for each TCP Tunnel: us-east-1-tcp.domotz.co:32784 Host: us-east-1-tcp.domotz.co Port: 32784 8. Open the .bat file as Administrator (see link below) and enter the requested information on the screen. 9. Connect the Global Configurator to the device on the loopback address that you choose (e.g. 127.0.0.100). Extron.bat
  4. Giancarlo

    TCP Tunnel - Crestron from remote

    Hi all, This is all the steps to connect from remote to your Savant controller using Domotz Pro: Crestron Instruction Select the Crestron Processor device from the Domotz WebApp → Device list → Device Go to "Connect" tab Click on "Open a TCP tunnel" Insert the Crestron Processor TCP Port. By default "41795" Wait to have the tunnel setup You get two informations: Host Port Open Crestron Toolbox program on your Laptop and: Open a new project Insert the previously retrieved Host/Port to be inserted here (see attachment as an example) Save & Apply Let us know if you have any problem.
  5. henriquesalvador

    TCP Tunnel - Savant from remote

    Hi all, This is all the steps to connect from remote to your Savant controller using Domotz Pro: Savant Instruction Select the Savant controller device Go to "Connect" tab Click on "Open a TCP tunnel" Insert the SSH TCP Port. By default "22" Wait to have the tunnel setup You get two informations: Host Port Determine the IP address of the remote HOST by pinging it from a terminal (we will update our UI to provide that directly from the portal): MacBook-Pro:~ user$ ping us-west-2-tcp.domotz.co PING us-west-2-tcp.domotz.co (52.33.68.100): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Open the Savant System Monitor program and: Change the scan type from Local Network to Secure Comm. Mode Insert the previously retrieved <Host_IP_Address>:Port to the field: Click on Refresh, it will ask the user and password of your system: Let us know if you have any problem. Henrique Salvador Domotz Support support@domotz.com
  6. henriquesalvador

    TCP Tunnel - Control4 Composer from remote

    Hi all, This is all the steps to connect from remote to your Control4 Director using Domotz Pro: Control4 Instruction Select the Control4 Director Go to "Connect" tab Click on "Create a TCP tunnel" Insert the Control4 Director TCP Port. By default "5021" Wait to have the tunnel setup You get two informations: Host Port Run as administrator the Control4.bat script (see attachment bellow) and enter the HOST and PORT previously provided. Open Control4 Composer and create a connection to the local address 127.0.0.1 (it will be forwarded to the Domotz TCP Tunnel). Let us know if you have any problem. Henrique Salvador Domotz Support support@domotz.com Control4.bat
×